Skip to content
Cracked Wall Repair

Wall brickwork crack repair throughout the UK

Cracked brickwork assessed and repaired using the method that fits the cause.

What this repair work covers

Brickwork crack repair for UK properties: a specialist identifies the crack type and cause, then carries out the appropriate repair to the masonry.

Cracks in brickwork can follow the mortar joints in a stepped pattern, run straight through the brick face, or appear as a horizontal split along a single course. Each pattern points to a different cause: differential settlement, mortar failure, thermal movement or lateral pressure from a floor or roof member. Identifying the cause is the first step, because a repair applied to an active crack will simply reopen.

A specialist looks at the crack type, its position in the wall and the surrounding construction before advising on the correct repair. Work may involve raking out and repointing, helical bar stitching, or crack injection, depending on what the assessment shows. A free quote is available once the wall and the extent of the cracking have been reviewed.

Get a free quote today

Tell a specialist the property address, describe the cracking or movement you have spotted, and state which service fits. A free quote is put in writing before any repair work begins.

  • Specialist firms available across the United Kingdom
  • Quotes provided with every submission
  • No pressure to go ahead

Get your free quote

Wall brickwork crack repair across the UK

Specialists wall brickwork crack repair at properties across the United Kingdom, including Birmingham · Edinburgh · Glasgow · Leeds · Liverpool · London · Manchester · Sheffield and many more areas; pick a town to learn about local ground conditions and what the work typically involves there

Do these match your walls?

  • Stepped fractures running through mortar joints up and across the wall face
  • Cracks that are wider at one end than the other, suggesting differential movement
  • Mortar joints that are recessed, crumbling or missing across sections of the wall face
  • Fractures running through the face of individual bricks rather than tracking along the joints
  • Cracks that reappeared after a previous repair, with no investigation of the underlying cause
  • Spalling or surface loss on brickwork where moisture has been unable to escape through the joints

Ask a specialist

How the repair work goes

  1. Wall condition check

    The specialist records every crack in the brickwork, noting its width, length, orientation and whether it runs through the brick, the mortar joint or both.

  2. Cause confirmed

    The likely cause, whether structural movement, thermal expansion, failed lintels or differential settlement, is identified before any repair method is selected.

  3. Repair carried out

    Depending on the cause and crack width, the specialist cuts out and replaces damaged bricks, rakes and repoints mortar joints, or installs helical bar reinforcement across the affected section.

  4. Surface finish

    Repaired joints and replaced bricks are finished to match the surrounding wall in colour, texture and joint profile, and loose debris is cleared from the work area.

What affects the scope of a brickwork crack repair

  • Establishing the cause before starting work

    Cracks in brickwork can result from foundation movement, wall tie failure, lintel failure, thermal expansion or a combination of factors. The specialist identifies the cause before selecting a repair method, because treating the visible crack without addressing what caused it is likely to allow the crack to reopen.

  • Mortar type and masonry compatibility

    Older brickwork laid in lime mortar requires a repair mortar that matches its flexibility and porosity. A mortar that is too hard puts stress on the brick face rather than the joint, which leads to surface spalling as the years pass. The specialist tests the existing mortar and selects a replacement mix that suits it.

  • Crack stitching versus repointing

    Narrow cracks that have stabilised may be addressed by raking out and repointing with a matched mortar. Wider cracks or those that cross multiple courses may require stainless steel helical bars grouted across the crack line to restore tensile strength before the joint is made good. The specialist chooses the method according to crack width, wall construction and the load the wall is carrying.

  • Making good after repair

    Once structural work is complete, the repaired area is repointed to match the surrounding brickwork in mortar colour and joint profile as closely as possible. A free quote covers the full scope of work, including any making good required to bring the wall back to a sound and presentable condition.

Crack and subsidence help across the UK

A written price before work begins. The specialist sets the full cost down on paper before any repair is confirmed or scheduled.

Findings recorded on paper. The specialist sets out the cause and extent of any ground movement in a written report.

Firms with area knowledge. Local specialists know the soil types and drainage faults that cause wall cracking.

Your call, your timing. Read the figures, raise any questions you have, and proceed only when you are ready to.