Skip to content
Cracked Wall Repair

Wall resin injection crack repair specialists UK

Structural cracks filled and bonded from within using injected resin.

What this repair work covers

Resin injection crack repair for UK properties: how a specialist fills and bonds structural cracks in masonry and concrete under controlled pressure.

Resin injection repairs structural cracks in masonry or concrete by pumping a low-viscosity resin into the crack under controlled pressure. The resin fills the full depth of the void, bonds the two faces together and restores load transfer across the break once it has cured.

This technique is used where a crack runs through a structural element and needs to be consolidated rather than simply sealed at the surface. A specialist will assess the crack width, depth and cause before deciding whether resin injection is the right method. Where active ground movement is still occurring, the underlying cause must be addressed first. A free quote is available once the crack location and condition have been reviewed.

Get a free quote today

Tell a specialist the property address, describe the cracking or movement you have spotted, and state which service fits. A free quote is put in writing before any repair work begins.

  • Specialist firms available across the United Kingdom
  • Quotes provided with every submission
  • No pressure to go ahead

Get your free quote

Wall resin injection crack repair across the UK

Specialists wall resin injection crack repair at properties across the United Kingdom, including Birmingham · Edinburgh · Glasgow · Leeds · Liverpool · London · Manchester · Sheffield and many more areas; pick a town to learn about local ground conditions and what the work typically involves there

Do these match your walls?

  • Settlement that a structural engineer links to voids or loosened material beneath a slab or footing
  • Subsidence that is localised to one or two corners rather than distributed uniformly across the building
  • A heritage or listed building where conventional mass-concrete underpinning would damage original fabric
  • Access to the affected area is too restricted for open excavation or heavy plant
  • Soil investigation data confirming the problem area sits at a depth that injected resin can adequately reach
  • Cracking that has continued after surface repairs, with movement records confirming it has not stopped

Ask a specialist

How the repair work goes

  1. Void location

    The specialist probes the ground or wall to map where voids and weak zones sit and determines the injection point spacing needed to reach them fully.

  2. Hole drilling

    Small-diameter holes are drilled at the calculated spacings, angled to reach the voids confirmed during the investigation stage.

  3. Resin injection repair

    Resin is injected through each drilled hole in measured increments while the specialist reads surface monitoring data to detect any shift in the structure overhead.

  4. Seal and record

    Each drill hole is filled flush with the surrounding surface once injection is complete, and a written log of injected volumes and level readings is issued.

Where resin injection is and is not suitable

  • When the method is appropriate

    Resin injection is suited to properties where settlement has developed because of voids or disturbed subsoil beneath the footing rather than a failure of the foundation structure itself. Contractors favour it where site access is tight, where digging would put neighbouring buildings at risk, or where the property is in use and ground-level disruption must be limited.

  • Ground type and suitability

    It performs reliably in loose sandy or silty soils and where voids have formed under a concrete slab. If deep shrinkable clay is still drying out, the specialist may advise a different repair method or pair resin injection with a further treatment. Soil conditions are checked and confirmed before any injection work starts.

  • Tracking movement and pressure during the injection process

    The specialist monitors structural movement throughout using levels, injecting resin in measured stages so the structure rises gradually to the target point. Going too far creates problems on a par with the original settlement, so the process is managed in controlled stages throughout.

  • When resin injection is not the right choice

    Resin injection is not suitable where load-bearing walls have moved substantially due to deep foundation failure. Any drain defect or ongoing clay shrinkage needs to be dealt with before or at the same time as lifting work, or the movement will come back. A free quote will confirm whether the method is appropriate for your property.

Crack and subsidence help across the UK

A written price before work begins. The specialist sets the full cost down on paper before any repair is confirmed or scheduled.

Findings recorded on paper. The specialist sets out the cause and extent of any ground movement in a written report.

Firms with area knowledge. Local specialists know the soil types and drainage faults that cause wall cracking.

Your call, your timing. Read the figures, raise any questions you have, and proceed only when you are ready to.